返回

MIL DTL 868 3A详细规范 阀液压定向控制四通10 50gpm通用规范（2014年1月14日）[取代MIL V 868 3]

ID：51625

大小：1.00 MB

页数：36页

时间：2023-03-23

金币：20

上传者：战必胜
AMSC N/A FSC 4810
INCH-POUND
MIL-DTL-868/3A(SH)
14 January 2014
SUPERSEDING
MIL-V-868/3(SH)
21 July 1989
DETAIL SPECIFICATION SHEET
VAVLES, HYDRAULIC DIRECTIONAL CONTROL, FOUR-WAY, 10-50 GPM
Reinstated after 14 January 2014 and may be used
for new and existing designs and acquisitions.
This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is
available for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of this specification sheet and
MIL-DTL-868.
1. GENERAL
1.1 Classification. Directional control valves covered by this specification sheet shall be designated using Part
or Identifying Numbers (PIN) as follows (see table V for examples of PINs) :
M
868
/3
-
WW
T
YYY
ZZ
X
Prefix to
indicate a
Military
specification
Specification
number
Applicable
specification
sheet number
(see 1.1.1)
Left side
operator
(see 1.1.2)
Spool type
(see 1.1.3)
Spool flow
paths (see
1.1.4)
Right side
operator
(see 1.1.5)
Fatigue
(see
1.1.6)
1.1.1 Applicable specification sheet number. Theapplicablespecificationsheetnumberdesignatesthevalve’s
performance characteristics (flow range, pressure losses, leakage, etc.) and mounting interface configuration.
Figures 1, 2, and 3 define the mounting interface configuration and maximum dimensions for valves with various
types of operators. Control valves covered by this specification sheet shall be of the integral slide and sleeve type.
1.1.2 Left side valve operator. The left side valve operator shall be designated by a two-character code. The
left hand operator shall be designated as the actuator shown to the left of the spool symbol. On the actual valve, this
corresponds to the actuator closest to the return port. For valves operated by a handle or lever, the two-character
code shall be in accordance with table I. The first character designates the type of operator in addition to the handle.
The second character is a number (0 to 7) and indicates the positions, if any, in which the valve spool may be
latched or detented. For valves without an operating handle, the left side operator shall be designated by a two-
character code in accordance with table II. The first letter designates the primary operator and the second letter
identifies secondary operator(s), if any. See 1.1.7 for special operator configurations not covered by tables I and II.
Downloaded from http://www.everyspec.com
资源描述：

当前文档最多预览五页，下载文档查看全文

此文档下载收益归作者所有

当前文档最多预览五页，下载文档查看全文
温馨提示：
1. 部分包含数学公式或PPT动画的文件，查看预览时可能会显示错乱或异常，文件下载后无此问题，请放心下载。
2. 本文档由用户上传，版权归属用户，天天文库负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容，确认文档内容符合您的需求后进行下载，若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误，付费完成后未能成功下载的用户请联系客服处理。
最近更新
更多
大家都在看
近期热门

分享

购物车

关闭